Home>Heating>Electric Heaters>Electric Unit Heaters
Markel | P3PUH10CA1 Fan Forced Horizontal Discharge Electric Unit Heater | 10.0 KW | 480 Volts 3 Phase 12.1 Amps
Markel P3PUH10CA1 Image

Markel | P3PUH10CA1 Fan Forced Horizontal Discharge Electric Unit Heater | 10.0 KW | 480 Volts 3 Phase 12.1 Amps

Item Id: Markel-P3PUH10CA1
Review this item Review this item
Your Price: $878.00
On sale:
$702.00
Usually Ships In: 10-15 Business Days
Ships By: UPS or FedEx Ground. Multiple quantities may ship via truck.
Weight: 51 (Lbs.)
Links To Product Literature:
Markel UH Catalog
Markel UH Installation Guide
Free Shipping
Quantity
Email a friend Email a friend
Add to Wish List Add to Wish List
Choose Options
Voltage And Amperage Confirmation *REQUIRED
I Have Confirmed That My Electrical Service Is Compatible With The Voltage And Amp Draw Of This Heater
Markel UH Thermostat *REQUIRED
No Thanks I Already Have A Thermostat
Remote Wall Mounted 24V Low Voltage Thermostat A6176 [+$58.00]
Markel UH Mounting Bracket
Wall Ceiling Bracket UHB-1-2 (Field Installed) [+$55.00]
Markel UH Factory Installed Options
Heat Purge Fan Delay Switch For 480 Volt Units (Contactor And Transformer Standard In Unit) Suffix-F [+$65.00]
Summer Fan Switch Suffix-S [+$32.00]
Epoxy Coating Suffix-E [+$62.00]
Disconnect Switch 30 Amp Suffix-D [+$155.00]
SPST Thermostat Suffix-T [+$37.00]
Markel UH Field Installed Accessories
30 Amp Disconnect Kit DCS303 [+$132.00]
Description

CONSTRUCTION:
Heavy Gauge welded steel cabinet with powder coated finish and control compartment with a hinged and latched access door, simplifying wiring installation & maintenance.

HEATING ELEMENT:
Circular copper clad steel sheath element with continuously brazed steel fins formed to match the air delivery pattern of the fan blade.

OVERHEAT PROTECTION:
All units come equipped with automatic resetting type limit controls to deenergize the heater should an over-temperature situation occur.

FAN and MOTOR:
Totally enclosed, single phase, permanently lubricated, thermally protected motors with unit bearings on 3 KW - 10 KW models and sleeve bearings on 12.5 KW - 48 KW models - mounted with rubber insulators to minimize vibration and noise. Fan assembly enclosed by a heavy Gauge, close spaced, chrome plated wire guard.

LOUVER ASSEMBLY:
Louvers are individually adjustable for directional control of air flow and the entire assembly can be repositioned in the field from down flow to up flow or left / right directional air flow.

TEMPERATURE CONTROLS:
20 KW through 48 KW units and all 480V have built in 24 Volt transformer for low voltage remote thermostat application. 25 KW through 48 KW models available in 2-stage on special order (consult factory).

INSTALLATION:
Unit Heaters can be mounted with the motor shaft from horizontal to downward at 45 off horizontal. Pre-drilled holes and installed threaded nuts provided to allow hanging by threaded rods - 1/4” for units up to 15 KW and 5/16” for 20 KW units and larger. Optional wall / ceiling mounting brackets are available for all units.

NOTE: Louver assembly is square and mounted with screws. Louver can be removed and repositioned for four (4) directional air flow - left - right - up - down with the heater in the horizontal position.

Markel
Recently Viewed Items
spacer
spacer